51單片機秒錶課程設計

Ⅰ 51單片機設計簡易秒錶

你學習板的圖呢？我怎麼知道用哪些IO口！怎麼知道你數碼管用什麼驅動啊！不然怎麼寫

Ⅱ 51單片機製作一個秒錶

//功能：0~99秒的簡易秒錶設計，兩個靜態數碼管，定時器採用中斷方式
#include"reg51.h"
#define uchar unsigned char
#define uint unsigned int

uchar count=0;//對50ms定時時間進行計數
uchar miao=0; //秒計數器

//函數名：timer_1()
//函數功能：定時器T1的中斷函數，T1在工作方式1下每50秒產生中斷，執行該中斷函數
//形式參數：無
//返回值：無
void timer_1() interrupt 3 //T1的中斷類型號為3
{
TH1=(65536-50000)/256; //重新設置T1計數初值高8位
TL1=(65536-50000)%256; //重新設置T1計數初值低8位
count++; //50ms計數器加1
if(count==20) //1s時間到
{
count=0; //50ms計數器清0
miao++; //秒計數器加1
if(miao==100)miao=0; //miao計數到100，則從0開始計數
}
}

bit b=0;
void int_0() interrupt 0
{
if(b == 0){TR1 = 0;b = 1;}
else
{
b = 0;
TR1 = 1;
}
}

void int_1() interrupt 2
{
miao=0;
count = 0;
TH1=(65536-50000)/256;
TL1=(65536-50000)%256;
TR1=1;
}

//函數名：disp
//函數功能：將i的值顯示在兩個靜態連接的數碼管上
//形式參數：i，取值范圍0~99
//返回值：無
void disp(uchar i)
{
uchar led[]={0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90};
//定義0~9顯示碼，共陽極數碼管
P1=led[i/10]; //顯示i高位
P2=led[i%10]; //顯示i地位
}
void main()
{
TMOD=0x10;//設置T1在工作方式1
TH1=(65536-50000)/256;//設置T1計數初值高8位，定時時間50ms
TL1=(65536-50000)%256;//設置T1計數初值低8位
ET1=1;//開放T1中斷允許
EX0 = 1;
IT0 = 1;
EX1 = 1;
IT1=1;
EA=1;//開放總中斷允許
TR1=1;//啟動T1開始計時
while(1)
{
disp(miao);//顯示秒計數器值
}
}

Ⅲ 51單片機完成簡易秒錶的設計

硬體電路簡單，我說下軟體部分
用一個定時器定時中斷做鍵盤掃描，數碼管用動態掃描的方法，數碼管顯示和按鍵處理都放在主程序中進行

Ⅳ 51單片機設計一個秒錶，用兩個數碼管（任意相鄰的兩個）顯示。

ORG 0000H
JMP BEGIN
ORG 000BH
LJMP T0INT
ORG 001BH
LJMP T1INT
LEDD EQU 30H
LEDC EQU 36H
SECC EQU 37H
TCNT EQU 3AH
ORG 0030H
;---------------------------------------
TABLE: ; 共陰極數碼管顯示代碼表
DB 0FCH ;"0" 00H
DB 60H ;"1" 01H
DB 0DAH ;"2" 02H
DB 0F2H ;"3" 03H
DB 66H ;"4" 04H
DB 0B6H ;"5" 05H
DB 0BEH ;"6" 06H
DB 0E0H ;"7" 07H
DB 0FEH ;"8" 08H
DB 0F6H ;"9" 09H
DB 0EEH ;"A" 0AH
DB 3EH ;"B" 0BH
DB 9CH ;"C" 0CH
DB 7AH ;"D" 0DH
DB 9EH ;"E" 0EH
DB 8EH ;"F" 0FH
DB 00H ;" " 10H
; DB 3FH,06H,5BH,4FH,66H ;12345
; DB 6DH,7DH,07H,7FH, ;6789
;---------------------------------------
DELAY:
MOV R6,#25
DLY01:
MOV R7,#100
DJNZ R7,$
DJNZ R6,DLY01
RET
;---------------------------------------
BEGIN:
MOV SP,#5FH
MOV TMOD,#11H
MOV TH0,#3CH
MOV TL0,#0B0H
MOV TH1,#0F4H
MOV TL1,#48H
MOV LEDC,#0
MOV R0,#LEDD
CLR A
INIT:
MOV @R0,A
INC R0
DJNZ LEDC,INIT
SETB ET1
SETB TR1
MOV P2,#0
MOV TCNT,#0
MOV SECC,#0
SETB ET0
SETB EA
MOV SECC,#60
LCALL DISSEC
SETB TR0
SETB TR1
LOOP:
SJMP $
;---------------------------------------
T1INT:
PUSH ACC
CLR TR1
MOV TH1,#0F4H
MOV TL1,#48H
SETB TR1
MOV DPTR,#TABLE
MOV R0,#LEDD
MOV A,LEDC
T1INT0:
JNZ T1INT1
MOV P2,#01H
MOV A,@R0
MOVC A,@A+DPTR
CPL A
MOV P0,A
SJMP T1INTD
T1INT1:
MOV P2,#02H
INC R0
MOV A,@R0
MOVC A,@A+DPTR
CPL A
MOV P0,A
T1INTD:
INC LEDC
MOV A,LEDC
CJNE A,#2,T1INT6
T1INT6:
JC T1INTE
MOV LEDC,#0
T1INTE:
POP ACC
RETI
;---------------------------------------
HBCD:
MOV B,#10
DIV AB
SWAP A
ORL A,B
RET
;---------------------------------------
T0INT:
PUSH ACC
CLR TR0
MOV TH0,#3CH
MOV TL0,#0B0H
SETB TR0
INC TCNT
MOV A,TCNT
CJNE A,#20,T0INT1
T0INT1:
JC T0INTE
MOV TCNT,#0
INC SECC
MOV A,SECC
CJNE A,#60,T0INT2
JC T0INT2
MOV A,#60
MOV SECC,A
T0INT2:
LCALL DISSEC
T0INTE:
POP ACC
RETI
;---------------------------------------
DISSEC:
MOV A,SECC
LCALL HBCD
PUSH ACC
ANL A,#0FH
MOV 30H,A
POP ACC
SWAP A
ANL A,#0FH
MOV 31H,A
RET
;---------------------------------------
END

Ⅳ 51單片機秒錶課程設計

你好，我空間裡面有的正好可以使用

強調一下，此文實為轉載，原因就是東西搞的不錯，放心使用

http://hi..com/lyzhangxiang/blog/item/c37397ef363abd2e2df53431.html

Ⅵ 51單片機秒錶設計,高手請進

正好,我的博客上有一個比較好的,是我2004年帶課程設計時所寫,你可以去看看.

Ⅶ 6位數碼管的MCS51單片機秒錶設計實驗

HD7279A.
ORG0000H
lJMPWAIT0
ORG001BH
LJMPBRT
ORG0030H
WAIT0:LCALLDISP
MOVC,P1.4
JCWAIT0
LCALLREAD
MOVA,28H
CJNEA,#01H,WAIT0
MIAOBIAO:MOV79H,#00H;1鍵開始
MOV7AH,#00H;2鍵停止
MOV7BH,#00H;再按3鍵清零
MOV7CH,#00H;再按1鍵重新開始
MOV7DH,#00H
MOV7EH,#00H
MOVTMOD,#10H
MOVTH1,#0D8H
MOV1,#0F0H
MOVIE,#88H
SETBPT1;中斷優先順序
SETBTR1;開啟定時器T1
;*********************************************************************************************
MAIN:ACALLDISP
MOVC,P1.4
JCMAIN;等按鍵，按2停止
ACALLREAD
MOVA,28H
CJNEA,#02H,MAIN
CLRTR1
WAIT1:LCALLDISP
MOVC,P1.4
JCWAIT1;按3鍵清零
LCALLREAD
MOVA,28H
CLR28H
CJNEA,#03H,WAIT1
MOV79H,#00H
MOV7AH,#00H
MOV7BH,#00H
MOV7CH,#00H
MOV7DH,#00H
MOV7EH,#00H
WAIT2:LCALLDISP
MOVC,P1.4;第三次按1鍵重新開始
JCWAIT2
LCALLREAD
MOVA,28H
CLR28H
CJNEA,#01H,EXIT
LJMPMIAOBIAO
EXIT:LJMPWAIT0
;EXIT:POPPSW
;POPACC
;RET
DISP:MOVR0,#79H
MOVR1,#0C8H
MOVR2,#06H
DISP_LOOP:MOV29H,R1
ACALLSEND
MOV29H,@R0
ACALLSEND
INCR1
INCR0
DJNZR2,DISP_LOOP
RET
SEND:CLRP1.7
MOVR3,#08H
lCALLLONG
SEND_LOOP:MOVC,29H.7
MOVP1.6,C
SETBP1.5
ACALLSHORT
CLRP1.5
ACALLSHORT
MOVA,29H
RLA
MOV29H,A
DJNZR3,SEND_LOOP
CLRP1.6
RET
LONG:MOVR5,#28H
LLP:DJNZR5,LLP
SHORT:MOVR6,#08H
SLP:DJNZR6,SLP
RET
BRT:MOVTL1,#0F0H
MOVTH1,#0D8H
PUSHPSW
PUSHACC
INC79H
MOVA,79H
CJNEA,#0AH,FH
MOV79H,#00H
INC7AH
MOVA,7AH
CJNEA,#0AH,FH
MOV7AH,#00H
INC7BH
MOVA,7BH
CJNEA,#0AH,FH
MOV7BH,#00H
INC7CH
MOVA,7CH
CJNEA,#06H,FH
MOV7CH,#00H
INC7DH
MOVA,7DH
CJNEA,#0AH,FH
MOV7DH,#00H
INC7EH
MOVA,7EH
CJNEA,#06H,FH
MOV7EH,#00H
FH:POPACC
POPPSW
RETI
READ:MOV29H,#15H
ACALLSEND
LCALLRESE
RET
RESE:MOV71H,#8;=8
SETBP1.6;P1.2(DATA)
CALLLONG;
RECEIVE_LOOP:SETBP1.5;CLK
CALLSHORT;
MOVA,28H;
RLA
MOV28H,A
MOVC,P1.6;
MOV28H.0,C
CLRP1.5;CLK
CALLSHORT
DJNZ71H,RECEIVE_LOOP;8
CLRP1.6;DAT
RET

Ⅷ 51單片機 秒錶設計

// 51單片機 秒錶，顯示時間為0000—9999秒，啟動、停止，（停止後再次啟動復位）

#include<reg52.h>

#define uint unsigned int

#define uchar unsigned char

uchar code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};

uchar ,shi;

uint a1,a2;

sbit D1=P3^0;

sbit D2=P3^1;

sbit D3=P3^2;

sbit D4=P3^3;

sbit key=P3^5;

sbit key1=P3^7;

bit j ;

uint y ;

void main()

{

TMOD=0x01;

TH0=(65536-10000)/256;

TL0=(65536-10000)%256;

EA=1;

ET0=1;

TR0=1;

=0;

shi=0;

while(1)

{

if(key==0)

{

j=0;

}

if(key1==0)

{

j=1; a2=0;

}

}

}

void timer0()interrupt 1

{

TH0=(65536-10000)/256;

TL0=(65536-10000)%256;

a1++;

y++;

if(a1==100)

{

a1=0;

if(j==1) a2++;

if(a2>=10000) a2=0;

}

D1 = 1; D2 = 1; D3 = 1; D4 = 1;

if(y==1)

{

P1=table[a2%10000/1000];

D4=0;

}

if(y==2)

{

P1=table[a2%1000/100];

D3=0;

}

if(y==3)

{

P1=table[a2%100/10];

D2=0;

}

if(y==4)

{

P1=table[a2%10];

D1=0;

y=0;

}

}

Ⅸ 用51單片機C語言版設計秒錶倒計時

K1 EQU P1.0
K2 EQU P1.1
K3 EQU P1.2
ORG 0000H
LJMP MAIN
ORG 000BH
LJMP T0ISR
ORG 0030H
MAIN:
MOV TMOD,#01H
MOV TH0,#HIGH(65536-10000)
MOV TL0,#LOW(65536-10000)
SETB ET0
SETB TR0
SETB EA
MOV R0,#9
MOV R1,#9
MOV R2,#0
MOV R3,#99
CLR 00H
CLR 01H
LOOP:
JB K1,LP01
JNB K1,$
CLR 01H
INC R3
CJNE R3,#100,LOOP0
MOV R3,#0
SJMP LOOP0
LP01:
JB K2,LP02
JNB K2,$
CLR 01H
CJNE R3,#0,LP011
MOV R3,#99
SJMP LOOP0
LP011:
DEC R3
SJMP LOOP0
LP02:
JB K3,LOOP
JNB K3,$
SETB 01H
SJMP LOOP
LOOP0:
MOV A,R3
MOV B,#10
DIV AB
MOV R0,B
MOV R1,A
SJMP LOOP
T0ISR:
CLR TR0
MOV TH0,#HIGH(65536-10000)
MOV TL0,#LOW(65536-10000)
SETB TR0
MOV DPTR,#TABLE
T0C:
CPL 00H
JB 00H,T001
MOV P3,#0FDH
MOV A,R1
MOVC A,@A+DPTR
MOV P2,A
SJMP T002
T001:
MOV P3,#0FEH
MOV A,R0
MOVC A,@A+DPTR
MOV P2,A
T002:
JNB 01H,T0E
INC R2
MOV A,R2
CJNE A,#100,T0E
MOV R2,#0
MOV A,R0
JZ T003
DEC R0
SJMP T0E
T003:
MOV A,R1
JZ T004
DEC R1
MOV R0,#9
T0E:
RETI
T004:
CLR 01H
MOV R4,#16
T005:
CPL P0.0
LCALL DELAY
DJNZ R4,T005
RETI
DELAY:
MOV R6,#200
DLY:
MOV R7,#250
DJNZ R7,$
DJNZ R6,DLY
RET
TABLE: ; 共陰極數碼管顯示代碼表
DB 3FH,06H,5BH,4FH,66H ;01234
DB 6DH,7DH,07H,7FH,6FH ;56789
END

Ⅹ 用51單片機設計一個秒錶。主要要求： 1.用單片機的定時/計數器實現一個

KEYVALEQU 30H
DATEQU 33H
SCANLEDEQU 39H
CLKEQU 77H
SECEQU 78H
SEC1EQU 79H
SEC2EQU 7AH
DOTBIT 00H
ORG 0000H
LJMP MAIN
ORG 0003H
LJMP EXTINT0
ORG 000BH
LJMP T0ISR;50ms定時
ORG 001BH
LJMP T1ISR;掃描顯示
ORG 0030H
MAIN:
MOV SP,#5FH
MOV TMOD,#11H
MOV TH0,#03CH
MOV TL0,#0B0H
MOV TH1,#0ECH
MOV TL1,#078H
MOV KEYVAL,#2
MOV 33H,#10H
MOV 34H,#10H
MOV 35H,#10H
MOV 36H,#10H
MOV CLK,#0
SETB IT0
SETB EX0
CLR TR0
CLR ET0
MOV R2,#0
SETB TR1
SETB ET1
SETB EA
LOOP:
MOV A,KEYVAL
LOOP1:
JNZ LOOP2;啟動
SETB TR0
SETB ET0
SJMP LOOP
LOOP2:
DEC A
JNZ LOOP3;暫停
CLR TR0
CLR ET0
SJMP LOOP
LOOP3:
DEC A
JNZ LOOP;清零
MOV 36H,#0
MOV 35H,#0
MOV 34H,#0
MOV 33H,#0
SJMP LOOP
EXTINT0:
PUSH ACC
INC KEYVAL
MOV A,KEYVAL
CJNE A,#3,EXT00
EXT00:
JC EXT01
MOV KEYVAL,#0
EXT01:
POP ACC
RETI
T0ISR:
PUSH ACC
CLR TR0
MOV TH0,#3CH
MOV TL0,#0B0H
SETB TR0
INC CLK
MOV A,CLK
CJNE A,#2,T0ISRE
MOV CLK,#0
INC 36H
MOV A,36H
CJNE A,#10,T0ISRE
MOV 36H,#0
INC 35H
MOV A,35H
CJNE A,#10,T0ISRE
MOV 35H,#0
INC 34H
MOV A,34H
CJNE A,#6,T0ISRE
MOV 34H,#0
INC 33H
MOV A,33H
CJNE A,#10,T0ISRE
MOV 33H,#0
T0ISRE:
POP ACC
RETI
T1ISR:
PUSH ACC
CLR TR1
MOV TH1,#0ECH
MOV TL1,#78H
SETB TR1
MOV DPTR,#LEDTAB
T100:
MOV R0,#DAT
MOV A,SCANLED
ADD A,R0
MOV R0,A
MOV A,SCANLED
JNZ T101
MOV P2,#01H
SETB DOT
SJMP T1DIS
T101:
DEC A
JNZ T102
MOV P2,#02H
CLR DOT
SJMP T1DIS
T102:
DEC A
JNZ T103
MOV P2,#04H
SETB DOT
SJMP T1DIS
T103:
MOV P2,#08H
CLR DOT
T1DIS:
MOV A,@R0
MOVC A,@A+DPTR
JNB DOT,T1DIS1
ORL A,#01H
T1DIS1:
CPL A
MOV P0,A
INC SCANLED
MOV A,SCANLED
CJNE A,#4,T1END
MOV SCANLED,#0
T1END:
POP ACC
RETI
LEDTAB:DB 0FCH;"0"00H
DB 60H;"1"01H
DB 0DAH;"2"02H
DB 0F2H;"3"03H
DB 66H;"4"04H
DB 0B6H;"5"05H
DB 0BEH;"6"06H
DB 0E0H;"7"07H
DB 0FEH;"8"08H
DB 0F6H;"9"09H
DB 0EEH;"A"0AH
DB 3EH;"B"0BH
DB 9CH;"C"0CH
DB 7AH;"D"0DH
DB 9EH;"E"0EH
DB 8EH;"F"0FH
DB 00H;" "10H
END