㈠ 基于C51单片机的信号发生器
一个数模转换器就可以了，利用定时器溢出中断实现，每次溢出中断对P0口赋值，通常是赋值你编写好的数组，因为你每次改变io口的状态，对应DA转换器输出电压的改变，从而产生波形，例如你要产生方波，你初值P0=0xff,进入中断（设变量A，然后A++）次数达到某个值（例如100）的时候P0取反，然后A清零，每次达到中断次数100就取反，从而产生方波；三角波，你就每次中断赋你写好的数组（从0v~5V单调增的数组）先用数组顺序赋值给P0口，达到最后数组的时候，就反过来赋值给P0口，这样就产生了三角波了。如果要改变频率的话，你就在中断加入个变量，这个变量用来给定时器赋重装值的，通过改变这个变量来改变定时时间，使频率改变。
㈡ 求一个正确的基于51单片机的函数信号发生器的C程序
#include<reg51.h>
#include<absacc.h>
#include<MAX72191.h>
#defineDAC XBYTE[0x7fff] //P2.7接CS
sbitkey0 = P3^2;// 增减切换键
sbitkey1 = P3^3;//个位,十位，百位，千位的控制切换
sbitkey2 = P3^4;// 调整位
sbitkey3 = P3^5;// 波形选择正弦、三角、矩形波，锯齿波
unsignedchar i,j;
unsignedint counter,step,flag;
typedefunsigned int uint;
//定时器0初始化
voidInit_Timer0(void)
{
TMOD = (TMOD & 0XF0) | 0X01;//设置工作方式和定时初始值
TH0 = 0xff;
TL0 = 0x00;
TR0 =1; //启动定时器
ET0 =1;
}
//定义输出波形的代码
unsignedchar code type[4][256]={
{ //正弦波代码
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x1, 0x1, 0x2, 0x3, 0x3, 0x4, 0x5, 0x6, 0x7, 0x8,
0x9, 0xb,0xc, 0xd, 0xf, 0x10,0x12,0x13,0x15,0x17,0x19,0x1b,0x1d,0x1f,0x21,0x23,
0x25,0x27,0x2a,0x2c,0x2e,0x31,0x33,0x36,0x39,0x3b,0x3e,0x41,0x43,0x46,0x49,0x4c,
0x4f,0x52,0x55,0x58,0x5b,0x5e,0x61,0x64,0x67,0x6a,0x6d,0x70,0x73,0x76,0x7a,0x7d,
0x80,0x83,0x86,0x89,0x8c,0x8f,0x93,0x96,0x99,0x9c,0x9f,0xa2,0xa5,0xa8,0xab,0xae,
0xb1,0xb4,0xb6,0xb9,0xbc,0xbf,0xc1,0xc4,0xc7,0xc9,0xcc,0xce,0xd1,0xd3,0xd5,0xd8,
0xda,0xdc,0xde,0xe0,0xe2,0xe4,0xe6,0xe8,0xea,0xeb,0xed,0xef,0xf0,0xf1,0xf3,0xf4,
0xf5,0xf6,0xf8,0xf9,0xf9,0xfa,0xfb,0xfc,0xfc,0xfd,0xfd,0xfe,0xfe,0xfe,0xfe,0xfe,
0xfe,0xfe,0xfe,0xfe,0xfe,0xfd,0xfd,0xfc,0xfc,0xfb,0xfa,0xf9,0xf9,0xf8,0xf6,0xf5,
0xf4,0xf3,0xf1,0xf0,0xef,0xed,0xeb,0xea,0xe8,0xe6,0xe4,0xe2,0xe0,0xde,0xdc,0xda,
0xd8,0xd5,0xd3,0xd1,0xce,0xcc,0xc9,0xc7,0xc4,0xc1,0xbf,0xbc,0xb9,0xb6,0xb4,0xb1,
0xae,0xab,0xa8,0xa5,0xa2,0x9f,0x9c,0x99,0x96,0x93,0x8f,0x8c,0x89,0x86,0x83,0x80,
0x7d,0x7a,0x76,0x73,0x70,0x6d,0x6a,0x67,0x64,0x61,0x5e,0x5b,0x58,0x55,0x52,0x4f,
0x4c,0x49,0x46,0x43,0x41,0x3e,0x3b,0x39,0x36,0x33,0x31,0x2e,0x2c,0x2a,0x27,0x25,
0x23,0x21,0x1f,0x1d,0x1b,0x19,0x17,0x15,0x13,0x12,0x10,0xf,0xd, 0xc, 0xb, 0x9,
0x8,0x7, 0x6, 0x5, 0x4, 0x3, 0x3, 0x2, 0x1, 0x1, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
},
{ //三角波代码
0x2,0x4, 0x6, 0x8, 0xa, 0xc, 0xe, 0x10,0x12,0x14, 0x16, 0x18, 0x1a,0x1c, 0x1e, 0x20,
0x22,0x24, 0x26, 0x28, 0x2a, 0x2c, 0x2e, 0x30,0x32, 0x34, 0x36, 0x38, 0x3a, 0x3c, 0x3e, 0x40,
0x42,0x44, 0x46, 0x48, 0x4a, 0x4c, 0x4e, 0x50,0x52, 0x54, 0x56, 0x58, 0x5a, 0x5c, 0x5e, 0x60,
0x62,0x64, 0x66, 0x68, 0x6a, 0x6c, 0x6e, 0x70,0x72, 0x74, 0x76, 0x78, 0x7a, 0x7c, 0x7e, 0x80,
0x82,0x84, 0x86, 0x88, 0x8a, 0x8c, 0x8e, 0x90,0x92, 0x94, 0x96, 0x98, 0x9a, 0x9c, 0x9e, 0xa0,
0xa2,0xa4, 0xa6, 0xa8, 0xaa, 0xac, 0xae, 0xb0,0xb2, 0xb4, 0xb6, 0xb8, 0xba, 0xbc,0xbe, 0xc0,
0xc2,0xc4, 0xc6, 0xc8, 0xca, 0xcc, 0xce, 0xd0,0xd2, 0xd4, 0xd6, 0xd8, 0xda, 0xdc,0xde, 0xe0,
0xe2,0xe4, 0xe6, 0xe8, 0xea, 0xec, 0xee, 0xf0,0xf2, 0xf4, 0xf6, 0xf8, 0xfa, 0xfc,0xfe, 0xff,
0xfe,0xfc, 0xfa, 0xf8, 0xf6, 0xf4, 0xf2, 0xf0,0xee, 0xec, 0xea, 0xe8, 0xe6, 0xe4,0xe2, 0xe0,
0xde,0xdc, 0xda, 0xd8, 0xd6, 0xd4, 0xd2, 0xd0,0xce, 0xcc, 0xca, 0xc8, 0xc6, 0xc4,0xc2, 0xc0,
0xbe,0xbc, 0xba, 0xb8, 0xb6, 0xb4, 0xb2, 0xb0,0xae, 0xac, 0xaa, 0xa8, 0xa6, 0xa4,0xa2, 0xa0,
0x9e, 0x9c, 0x9a, 0x98, 0x96, 0x94, 0x92, 0x90,0x8e, 0x8c, 0x8a, 0x88, 0x86, 0x84, 0x82, 0x80,
0x7e, 0x7c, 0x7a, 0x78, 0x76, 0x74, 0x72, 0x70,0x6e, 0x6c, 0x6a, 0x68, 0x66, 0x64, 0x62, 0x60,
0x5e, 0x5c, 0x5a, 0x58, 0x56, 0x54, 0x52, 0x50,0x4e, 0x4c, 0x4a, 0x48, 0x46, 0x44, 0x42, 0x40,
0x3e, 0x3c, 0x3a, 0x38, 0x36, 0x34, 0x32, 0x30,0x2e, 0x2c, 0x2a, 0x28, 0x26, 0x24, 0x22, 0x20,
0x1e, 0x1c, 0x1a, 0x18, 0x16, 0x14, 0x12, 0x10,0xe, 0xc, 0xa, 0x8, 0x6, 0x4, 0x2, 0x00
},
{// 矩形脉冲波代码
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
},
{//锯齿波代码
0x00,0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,0x08,0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
0x10,0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17,0x18,0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f,
0x20,0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27,0x28,0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f,
0x30,0x31, 0x32, 0x33, 0x34, 0x35, 0x36, 0x37,0x38,0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f,
0x40,0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,0x48,0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f,
0x50,0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57,0x58,0x59, 0x5a, 0x5b, 0x5c, 0x5d, 0x5e, 0x5f,
0x60,0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67,0x68,0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f,
0x70,0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77,0x78,0x79, 0x7a, 0x7b, 0x7c, 0x7d, 0x7e, 0x7f,
0x80,0x81, 0x82, 0x83, 0x84, 0x85, 0x86, 0x87,0x88,0x89, 0x8a, 0x8b, 0x8c, 0x8d, 0x8e, 0x8f,
0x90,0x91, 0x92, 0x93, 0x94, 0x95, 0x96, 0x97,0x98,0x99, 0x9a, 0x9b, 0x9c, 0x9d, 0x9e, 0x9f,
0xa0,0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa6, 0xa7,0xa8,0xa9, 0xaa, 0xab, 0xac, 0xad, 0xae, 0xaf,
0xb0,0xb1, 0xb2, 0xb3, 0xb4, 0xb5, 0xb6, 0xb7,0xb8,0xb9, 0xba, 0xbb, 0xbc, 0xbd, 0xbe, 0xbf,
0xc0,0xc1, 0xc2, 0xc3, 0xc4, 0xc5, 0xc6, 0xc7,0xc8,0xc9, 0xca, 0xcb, 0xcc, 0xcd, 0xce, 0xcf,
0xd0,0xd1, 0xd2, 0xd3, 0xd4, 0xd5, 0xd6, 0xd7,0xd8,0xd9, 0xda, 0xdb, 0xdc, 0xdd, 0xde, 0xdf,
0xe0,0xe1, 0xe2, 0xe3, 0xe4, 0xe5, 0xe6, 0xe7,0xe8,0xe9, 0xea, 0xeb, 0xec, 0xed, 0xee, 0xef,
0xf0,0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7,0xf8,0xf9, 0xfa, 0xfb, 0xfc, 0xfd, 0xfe, 0xff}
};
//显示子函数
Disp7219(unsignedlong dat)
{
unsigned char i;
unsigned char led[8];
led[7]=dat%10;
led[6]=dat/10%10;
led[5]=dat/100%10;
led[4]=dat/1000%10;
led[3]=dat/10000%10;
led[2]=dat/100000%10;
led[1]=dat/1000000%10;
led[0]=dat/10000000%10;
for(i=0;i<8;i++)
{
max_7219(i+1, led[i]);
}
}
//延时约1m秒
voiddelay_ms(uint n)
{
uchar j;
while(n--)
for(j=0;j<120;j++);
}
//主函数
main()
{
unsigned int f,n,j;
delay_ms(500);
Init_Max7219();//初始化7219
Disp7219(000);
Init_Timer0();
step=18;
EA = 1;
while(1)
{
if(key0 == 0) n=n+1;
if(n==2)n=0;
if(key1==0) j=j+1;
if(j==4) j=0;
if(n==0 && j == 0 &&key2 == 0) if(step<180) step+=18; //个位增
if(n==1 && j == 0 &&key2 == 0) if(step>18) step-=18; //个位减
if(n==0 && j == 1 &&key2 == 0) if(step<1800) step+=180;//十位增
if(n==1 && j == 1 &&key2 == 0) if(step>180) step-=180; //十位减
if(n==0 && j == 2 &&key2 == 0) if(step<18000) step+=1800;//百位增
if(n==1 && j == 2 &&key2 == 0) if(step>1800) step-=1800;//百位减
if(n==0 && j == 3 &&key2 == 0) if(step<54000) step+=18000;//千位增
if(n==1 && j == 3 &&key2 == 0) if(step>18000) step-=18000;//千位减
if(key3==0)flag=flag+1;if(flag==4)flag=0;
while((!key0)||(!key1)||(!key2)||(!key3));
f=step/18;
Disp7219(f);}//显示频率
}
// 定时中断服务
voidTimer0(void) interrupt 1 using 2
{
TH0 = 0xff;
TL0 = 0x00;
counter = counter + step;
DAC=type[flag][(unsignedint)counter>>8];
}
㈢ 基于51单片机的三角波信号发生器制作需要什么材料基本的制作流程是怎样的呢
单片机一片，DA芯片一片，放大电路
单片机接DA芯片，DA芯片接放大电路，如果需要调节电压幅度，放大电路可以选择可变增益放大，用单片机控制数字电位器实现。。。
㈣ 51单片机键控信号发生器
发现我去年做了一个这样的，不过我只弄了3种波形，频率方波的2K这样，正弦波就比较小了，250HZ以内。按键控制波形切换、频率增减，幅度增减
㈤ 如何用51单片机设计出一个任意波形信号发生器
这个需要DA转换芯片，将要产生的波形数字化，存入数组中，由单片机按顺序依次送往DA芯片进行转换，例如产生正弦波，频率50HZ,可以用100个点来描述，每隔200uS送1个数据，100个数据花20ms.数字化点越多，波形越完美，但也与你的DA芯片精度有关，8位DA只能输入256个数字量，很难得到很好的波形
㈥ 51单片机信号发生器原理
基于单片机的的信号发生器大概有两种形式，1、全部波形信号由单片机软件产生，再经由D/A转换输出；
2、单片机+专用信号发生系芯片，这种方式单片机仅扮演主控角色，信号由芯片硬件产生；